 | $ 52.25 Call us for Availability
LunaCrete® Roller Coat is a one component, high performance blend of high quality Portland cement, modified Co-Polymers, and Iron Oxide Pigments. It is designed for maximum strength, flexibility, adhesion, abrasion resistance, and freeze/thaw resistance. LunaCrete uses all of the necessary ingredients and pre-blends them in a controlled environment. This ensures the proper ratios of copolymer to cement, and cement to pigments are consistent. This promotes both product and color consistency saving you time on the job-site. This formulation may be used for many different decorative applications.
Printable Version | PRODUCT USES
LunaCrete® Roller Coat Mix is widely used to restore color on existing decorative concrete surfaces. Roller Coat can be used on existing stamped concrete surface that has worn, or to unify new stamped areas that may have color inconsistencies. Roller Coat can be used to color any decorative concrete surface without changing the appearance of pattern and/or texture.
Roller Coat is ideal for coloring:
Broom Textured finishes Stamped Concrete Commercial
Spray Textured finishes Stamped Overlays Industrial
May be Chemically Stained Interior and exterior Residential
SURFACE PREPARATION
The concrete surface must be clean and free from all sealers, paints, grease, oil or any other contaminates. Thoroughly degrease and ash the concrete surface. Using 4 parts water and 1 part Muriatic Acid flood the surface using a broom to spread the solution evenly.
Using a pressure washer completely wash the surface, making sure to rinse the surface clean. Allow the surface to dry before applying Roller Coat.
MIXING
Measure 2.5 Gallons of cool clean water, add 2 Color Packs and mix for 1 minute using a drill with a paddle mixer. Slowly add the Roller Coat to the water while mixing. Mix thoroughly for 2 minutes. The finished product should be the consistency of a thick paint.
APPLICATION
Lightly mist the concrete surface with cool clean water, Do Not Puddle. Using a heavy nap ( ½ or larger) apply the Roller Coat making sure to get an even application without roller marks. Recommended application is 2 coats, change direction between coats. It may be necessary to thin the product with a small amount of water if it thickens during application.
ANTIQUING
Stamped patterns may be antiqued after the Roller Coat has dried for a period of at least 24 hours using LunaCrete® Color Wash.
SEALING
After the antiquing has dried completely, the surface should be sealed with 3 coats of LunaCrete® Klear Koat Sealer.
Wait 1 hour between coats, adding LunaCrete® Monkey-Grip skid resistant additive if desired.
COVERAGE
1 container covers 400-600 Sq Ft Material Safety Data
for Roller Coat Mix | SUPPLIER IDENTIFICATION LunaCrete® 1111 H. Enterprise Court Holly Hill, FL 32117 386-252-4243
Emergency Phone Number:
1-800-424-9300
Roller Coat Mix may be used to comply with OSHA's Hazard Communication Standard (HCS), 29 CFR 1910, 1200. Standard must be consulted for specific requirements.
The precise composition of this product is proprietary information. A more complete disclosure can be provided in the event of a medical emergency.
HMIS Hazardous Materials Identification System | HEALTH | 1 | FIRE | 0 | REACTIVITY | 0 | PROTECTION | E |
HMIS Number Codes
4 - Severe
3 - Serious
2 - Moderate
1 - Slight
0 - Minimal
HMIS Protective Equipment Codes
A - safety glasses
B - safety glasses and gloves
C - safety glasses, gloves and an apron
D - face shield, gloves and an apron
E - safety glasses, gloves and a dust respirator
F - safety glasses, gloves, apron and a dust respirator
G - safety glasses, a vapor respirator
H - splash goggles, gloves, apron and a vapor respirator
I - safety glasses, gloves and a dust/vapor respirator
J - splash goggles, gloves, apron and a dust/vapor respirator
K - airline hood or mask, gloves, full suit and boots
The Material Safety Data provided on this website is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guide for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered as a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other material or in any process, unless specified in the text.
Product will perform as indicated by product specification sheet. Any adulteration will negate LunaCrete liability. |
HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
COMPONENTS
Silica Crystaline Quartz
CAS # 144808-60-7
PER CENT 60%-70%
OSHA PEL 8H TWA (Quartz/m3) 0.1 mg/m3(Respirable dust)
ACGIH TLV TWA 0.1 mg/m3 (Total Dust)
Portland Cement
CAS # 6599-15-1
PER CENT 30%-40%
OSHA PEL 8H TWA 10mg/m3 (Total Dust)
ACGIH TLV 50 MPPCP
For industrial use only.
•Major = Over 25 % , Minor = Over 6. 25 % , Trace = Under 6 %, Residue = Unknown % residue possible
PHYSICAL/CHEMICAL CHARACTERISTICS
SPECIFIC GRAVITY (H2O = 1): 2.7
EVAPORATION RATE (Butyl Acetate = 1):N/A
MATERIAL V.O.C.: N/A
APPEARANCE & ODOR: Gray or colored Finely ground, Odorless
SOLUBILITY IN WATER: Soluble
% VOLATILE BY VOLUME: 0
FIRE & EXPLOSION HAZARD DATA
FLASH POINT:
N/A
FLAMMABLE LIMITS IN AIR BY VOLUME:
LOWER: N/A UPPER: N/A
EXTINGUISHING MEDIA:
No Fire or Explosion Hazard
SPECIAL FIREFIGHTING PROCEDURES:
N/A
UNUSUAL FIRE & EXPLOSION HAZARDS:
N/A
REACTIVITY DATA
STABILITY: STABLE
CONDITIONS TO AVOID:
Although NO Hazardous reaction will occur products should be kept dry until used.
INCOMPATIBILITY (CONDITIONS OR MATERIALS TO AVOID):
None
HAZARDOUS DECOMPOSITON OR BYPRODUCTS:
None known
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR
HEALTH HAZARD DATA
A) HEALTH HAZARDS
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Avoid overexposure. Inhalation may cause irritation of respiratory tract and could promote coughing, dizziness and headache.
EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Eye contact: Direct contact irritates slightly with redness and swelling. Dust Irritant
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Abrasive
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Ingestion: May cause gastrointestinal obstruction.
CARCINOGENICITY:
NTP: NO
IARC MONOGRAPHS: Limited evidence as a Human Carcinogen
OSHA REGULATED ? See ingredients under Section 1.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Signs & Symptoms of Overexposure: 1. Shortness of Breath 2. Difficulty Breathing 3. Coughing and phlegm production. 4. More colds or infections than usual.
B) EMERGENCY AND FIRST AID PROCEDURES
INGESTION: May cause obstruction.
INHALATION: If respiratory irritation or distress occurs, remove victim to fresh air. Seek medical attention if respiratory irritation or distress continues.
SKIN ABSORPTION: If contact to the skin, wash thoroughly with soap and water. Seek medical attention if irritation or distress continues. Seek medical attention.
EYE CONTACT: If contact with eyes, hold eyes open and flush with a steady, gentle stream of water for at least 15 minutes. Seek medical attention if irritation or visual changes occur.
PRECAUTIONS FOR SAFE HANDLING & USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Sweep up material and remove to disposal container. Mop with mild detergents or cleaning solutions. Observe all relevant federal, state and local laws.
WASTE ISPOSAL METHOD
Sweep up but avoid creating excessive dust. ADDITION TO WATER WILL CAUSE MATERIAL TO SET UP. Any approved solid waste disposal method. A slurry of material may cause plugged drains.
PRECAUTIONS TO BE TAKEN IN HANDLING & STORING
Handling: wear gloves, eye protection and wear approved respirator. Wash hands before eating, drinking, using tobacco, applying cosmetics or using toilet.
Storage: do not store, use and/or consume foods, beverages, tobacco products or cosmetics in areas where this material is stored
OTHER PRECAUTIONS
Before using any LunaCrete products, read the label thoroughly.
CONTROL MEASURES
RESPIRATORY PROTECTION
Dust mask recommended- NIOSH or OSHA approved
VENTILLATION
Use local exhaust ventilation to control emissions at its source, preventing dispersion of it in the general work area.
PROTECTIVE GLOVES
Gloves may be worn for protection if skin is sensitive. (latex, neoprene, nitrile rubber)
EYE PROTECTION
Use safety glasses, goggles or face-shields for eye protection.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
NONE
WORK/HYGIENE PRACTICES
Avoid breathing dust. Wash hands thoroughly after handling and keep containers closed.
|
For additional information contact: LunaCrete® 1111 H. Enterprise Court Holly Hill, FL 32117 (866) 386-9122 - Toll Free |  | If you have already purchased access to an online video, |
|
|
Professional Products |
Online Catalog |
Complete DVD Set |
|
