2012.02.05
Online Catalog
Enter keyword
Broom Finish Tint Base

$ 34.75
Shipping Costs Vary About Shipping...
Call us for Availability

LunaCrete® Broom Finish is a one component, high performance blend of high quality Portland Cement, modified Co-Polymers, Silica Sand and Iron Oxide Pigments. It is designed for maximum Strength, flexibility, adhesion, abrasion resistance, and freeze/thaw resistance. By having all of the necessary ingredients pre-blended in a controlled environment, proper ratios of Co-Polymer to cement, and cement to pigments is consistent, which promotes product consistency, color consistency, and because of the unusual characteristics of this formulation, it may be used for many different applications.
Printable Version
Advantages
• Superior Adhesion
• Abrasion Resistant
• Weather / Stain Resistant
• Maximum Flexibility
• Extended Set Time
• UV Stable
• May be Chemically Stained
• From Featheredge
• Colors will not fade
• Enhances job

Benefits

• Non-shrink for maximum adhesion anddurability
• Resistant to freeze thaw and automotive vehicular traffic
• Thermal expansion similar to concrete
• Easy to trowel, broom, squeegee or spray apply to achieve desired finish
• Enhance property value, cost effective
• Works on vertical as well as horizontalsurfaces
• One component: just add water.
• Available in 25 standard colors as Neutral Gray to resemble cured concrete for
maximum blend / hide.
• Moisture insensitive after curing
• Resists staining when properly sealed.

Basic Uses

LunaCrete® Broom Finish is widely used to resurface and restore existing concrete surfaces. The LunaCrete® surface restoration system provides an attractive decorative appearance to irregular, worn and damaged concrete as well as new concrete surfaces.

Use For

Commercial Residential
Patching and Repairing Industrial
Broomed / Textured finishes Interior and exterior

Mix Ratio: 1-45 Lb. Pail/Bag Broom Finish to 1 gallons 1-1/4 gallons clean cool water.
Material Safety Data
for Broom Finish Tint Base
SUPPLIER IDENTIFICATION
LunaCrete®
1111 H. Enterprise Court
Holly Hill, FL 32117
386-252-4243

Emergency Phone Number:
1-800-424-9300

Broom Finish Tint Base may be used to comply with OSHA's Hazard Communication Standard (HCS), 29 CFR 1910, 1200. Standard must be consulted for specific requirements.

The precise composition of this product is proprietary information. A more complete disclosure can be provided in the event of a medical emergency.

HMIS
Hazardous Materials Identification System
HEALTH
1
FIRE
0
REACTIVITY
0
PROTECTION
E
HMIS Number Codes
4 - Severe
3 - Serious
2 - Moderate
1 - Slight
0 - Minimal

HMIS Protective Equipment Codes
A - safety glasses
B - safety glasses and gloves
C - safety glasses, gloves and an apron
D - face shield, gloves and an apron
E - safety glasses, gloves and a dust respirator
F - safety glasses, gloves, apron and a dust respirator
G - safety glasses, a vapor respirator
H - splash goggles, gloves, apron and a vapor respirator
I - safety glasses, gloves and a dust/vapor respirator
J - splash goggles, gloves, apron and a dust/vapor respirator
K - airline hood or mask, gloves, full suit and boots



The Material Safety Data provided on this website is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guide for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered as a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other material or in any process, unless specified in the text.

Product will perform as indicated by product specification sheet. Any adulteration will negate LunaCrete liability.
HAZARDOUS INGREDIENTS/IDENTITY INFORMATION

COMPONENT:Silica Crystaline Quartz
CAS #:144808-60-7
PER CENT:60%-70%
OSHA PEL:8H TWA 0.1 mg(Quartz/m3) (Respirable dust)
ACGIH TLV:TWA 0.1 0.1 mg/m3 (Respirable dust)

COMPONENT:Portland Cement
CAS #:6599-15-1
PER CENT:30%-40%
OSHA PEL:8H TWA 10mg/m3 (Total Dust)
ACGIH TLV: 50 MPPCF

Major = Over 25 % , Minor = Over 6. 25 % , Trace = Under 6 %, Residue = Unknown % residue possible

PHYSICAL/CHEMICAL CHARACTERISTICS

SPECIFIC GRAVITY (H2O = 1): 2.7
EVAPORATION RATE (Butyl Acetate = 1): N/A
MATERIAL V.O.C.: N/A
APPEARANCE & ODOR: White or colored Finely ground, Odorless
SOLUBILITY IN WATER: Soluble
% VOLATILE BY VOLUME: 0

FIRE & EXPLOSION HAZARD DATA

FLASH POINT:
N/A

FLAMMABLE LIMITS IN AIR BY VOLUME:
LOWER: N/A UPPER: N/A

EXTINGUISHING MEDIA:
No Fire or Explosion Hazard

SPECIAL FIREFIGHTING PROCEDURES:
N/A

UNUSUAL FIRE & EXPLOSION HAZARDS:
N/A


REACTIVITY DATA

STABILITY: STABLE

CONDITIONS TO AVOID:
Although NO Hazardous reaction will occur products should be kept dry until used.

INCOMPATIBILITY (CONDITIONS OR MATERIALS TO AVOID):
None

HAZARDOUS DECOMPOSITON OR BYPRODUCTS:
None known

HAZARDOUS POLYMERIZATION: WILL NOT OCCUR


HEALTH HAZARD DATA


A) HEALTH HAZARDS

INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Avoid overexposure. Inhalation may cause irritation of respiratory tract and could promote coughing, dizziness and headache.

EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Eye contact: Direct contact irritates slightly with redness and swelling. Dust Irritant

SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Abrasive

INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Ingestion: May cause gastrointestinal obstruction.

CARCINOGENICITY:
NTP? NO IARC MONOGRAPHS? Limited evidence as a Human Carcinogen
OSHA REGULATED ? See ingredients under Hazardous Ingredients/Identity Information.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Signs & Symptoms of Overexposure: 1. Shortness of Breath 2. Difficulty Breathing 3. Coughing and phlegm production. 4. More colds or infections than usual.

B) EMERGENCY AND FIRST AID PROCEDURES

INGESTION:
May cause obstruction.

INHALATION:
If respiratory irritation or distress occurs, remove victim to fresh air. Seek medical attention if respiratory irritation or distress continues.

SKIN ABSORPTION:
If contact to the skin, wash thoroughly with soap and water. Seek medical attention if irritation or distress continues. Seek medical attention.

EYE CONTACT:
If contact with eyes, hold eyes open and flush with a steady, gentle stream of water for at least 15 minutes. Seek medical attention if irritation or visual changes occur.


PRECAUTIONS FOR SAFE HANDLING & USE


STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Sweep up material and remove to disposal container. Mop with mild detergents or cleaning solutions. Observe all relevant federal, state and local laws.

WASTE ISPOSAL METHOD
Sweep up but avoid creating excessive dust. ADDITION TO WATER WILL CAUSE MATERIAL TO SET UP. Any approved solid waste disposal method. A slurry of material may cause plugged drains.

PRECAUTIONS TO BE TAKEN IN HANDLING & STORING
Handling: wear gloves, eye protection and wear approved respirator. Wash hands before eating, drinking, using tobacco, applying cosmetics or using toilet.
Storage: do not store, use and/or consume foods, beverages, tobacco products or cosmetics in areas where this material is stored

OTHER PRECAUTIONS
Before using any LunaCrete products, read the label thoroughly.


CONTROL MEASURES

RESPIRATORY PROTECTION
Dust mask recommended- NIOSH or OSHA approved

VENTILLATION
Use local exhaust ventilation to control emissions at its source, preventing dispersion of it in the general work area.

PROTECTIVE GLOVES
Gloves may be worn for protection if skin is sensitive. (latex, neoprene, nitrile rubber)

EYE PROTECTION
Use safety glasses, goggles or face-shields for eye protection.

OTHER PROTECTIVE CLOTHING OR EQUIPMENT
NONE

WORK/HYGIENE PRACTICES
Avoid breathing dust. Wash hands thoroughly after handling and keep containers closed.



For additional information contact:
LunaCrete®
1111 H. Enterprise Court
Holly Hill, FL 32117
(866) 386-9122 - Toll Free