 | $ 44.00 Call us for Availability
A Co-Polymer-Modified Overlay patching and leveling compound and bonding agent.
Printable Version | PRODUCT DESCRIPTION
LunaCrete® Bond Coat is a one component, high perfor¬mance blend of high quality Portland Cement, modified Co-Polymers, Silica Sand and Iron Oxide Pigments. It is designed for maximum Strength, flexibility, adhesion, abrasion resistance, and freeze/thaw resistance. By having all of the necessary ingredients pre-blended in a controlled environment, proper ratios of Co-Polymer to cement, and cement to silica sand is consistent, which promotes product uniformity, and because of the unusual characteristics of this formulation, it may be used for many different applications.
Advantages
•Superior Adhesion
•Abrasion Resistant
•Maximum Flexibility
•Extended Set Time
•UV Stable
•May be Chemically Stained
•From Featheredge to several inches in thickness
•Enhances job productivity and reduces job-site errors.
•Superior for patching and leveling concrete
•Initial cure in 1 hour (based on 1/32 inch)
•Superior bond strength.
Benefits
•Non-shrink for maximum adhesion and durability
•Resistant to freeze thaw and automotive vehicular traffic
•Thermal expansion similar to concrete
•Easy to trowel, broom, squeegee or spray apply to achieve desired finish
•Superior bond strength on cured to cured, or fresh to cured concrete.
•Works on vertical as well as horizontal surfaces
•One component: just add water.
•Moisture insensitive after initial cure.
Basic Uses
LunaCrete® Bond Coat is widely used to resurface and restore existing concrete surfaces. The LunaCrete® surface restoration system provides an attractive appearance to irregular, worn and damaged concrete surfaces.
Use For
Concrete Bonding
Patching / Leveling and Repairing
Broomed / Textured finishes
Commercial / Residential
Industrial
Interior and exterior
Mix Ratio
1-45 Lb. Pail/Bag Bond Coat to 1-1/2 gallons clean cool water.
TECHNICAL DATA
Compressive Strength
28 Days Air Cure 5200 psi
Tensile Strength
28 Days Air Cure 740 psi
Flexural Strength
28 Days Air Cure 2145 psi
Impact Strength (IN-BS.)
28 Days Air Cure 20
Abrasion Resistance
% Weight Loss
28 Days Air Cure 1.15
Shear Bond
28 Days Air Cure 2560 psi
Coverage (Approximately)
140 sq. ft. at 1/32”-70 sq. ft. at 1/16”
35 sq. ft. at 1/4" - 40 sq. ft. at 3/8"
Thermal Compatibility - 5 cycles no delaminating
Scaling - 25 cycles, none
*Testing results from an Independent Laboratory *The information contained herein is based on data believed to be reliable, but LunaCrete, Inc. makes no warranties expressed or implied as to it's accuracy and assumes no liability arising out of it's use by others.
Material Safety Data
for Bond Coat | SUPPLIER IDENTIFICATION LunaCrete® 1111 H. Enterprise Court Holly Hill, FL 32117 386-252-4243
Emergency Phone Number:
1-800-424-9300
Bond Coat may be used to comply with OSHA's Hazard Communication Standard (HCS), 29 CFR 1910, 1200. Standard must be consulted for specific requirements.
The precise composition of this product is proprietary information. A more complete disclosure can be provided in the event of a medical emergency.
HMIS Hazardous Materials Identification System | HEALTH | 1 | FIRE | 0 | REACTIVITY | 0 | PROTECTION | E |
HMIS Number Codes
4 - Severe
3 - Serious
2 - Moderate
1 - Slight
0 - Minimal
HMIS Protective Equipment Codes
A - safety glasses
B - safety glasses and gloves
C - safety glasses, gloves and an apron
D - face shield, gloves and an apron
E - safety glasses, gloves and a dust respirator
F - safety glasses, gloves, apron and a dust respirator
G - safety glasses, a vapor respirator
H - splash goggles, gloves, apron and a vapor respirator
I - safety glasses, gloves and a dust/vapor respirator
J - splash goggles, gloves, apron and a dust/vapor respirator
K - airline hood or mask, gloves, full suit and boots
The Material Safety Data provided on this website is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guide for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered as a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other material or in any process, unless specified in the text.
Product will perform as indicated by product specification sheet. Any adulteration will negate LunaCrete liability. | HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
COMPONENTS
Silica Crystaline Quartz
CAS # 144808-60-7
PER CENT 10%-30%
OSHA PEL 8H TWA 0.1 mg(Quartz/m3) (Respirable dust)
ACGIH TLV TWA 0.1 mg/m3 (Respirable dust)
Portland Cement
CAS # 6599-15-1
PER CENT 70%-90%
OSHA PEL 8H TWA 10mg/m3 (Total Dust)
ACGIH TLV 50 MPPCP
For industrial use only.
•Major = Over 25 % , Minor = Over 6. 25 % , Trace = Under 6 %, Residue = Unknown % residue possible
PHYSICAL/CHEMICAL CHARACTERISTICS
SPECIFIC GRAVITY (H2O = 1): 2.7
EVAPORATION RATE (Butyl Acetate = 1): N/A
MATERIAL V.O.C.: N/A
APPEARANCE & ODOR: Gray or colored Finely ground, Odorless
SOLUBILITY IN WATER: Soluble
% VOLATILE BY VOLUME: 0
FIRE & EXPLOSION HAZARD DATA
FLASH POINT: N/A
FLAMMABLE LIMITS IN AIR BY VOLUME: LOWER: N/A UPPER: N/A
EXTINGUISHING MEDIA: No Fire or Explosion Hazard
SPECIAL FIREFIGHTING PROCEDURES: N/A
UNUSUAL FIRE & EXPLOSION HAZARDS: N/A
REACTIVITY DATA
STABILITY: STABLE
CONDITIONS TO AOID:
Although NO Hazardous reaction will occur products should be kept dry until used.
INCOMPATIBILITY (CONDITIONS OR MATERIALS TO AVOID): None
HAZARDOUS DECOMPOSITON OR BYPRODUCTS: None known
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR
HEALTH HAZARD DATA
A) HEALTH HAZARDS
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Avoid overexposure. Inhalation may cause irritation of respiratory tract and could promote coughing, dizziness and headache.
EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Eye contact: Direct contact irritates slightly with redness and swelling. Dust Irritant
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Abrasive
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Ingestion: May cause gastrointestinal obstruction.
CARCINOGENICITY: NTP: NO IARC MONOGRAPHS: Limited evidence as a Human Carcinogen
OSHA REGULATED: See ingredients under HAZARDOUS
INGREDIENTS/IDENTITY INFORMATION
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Signs & Symptoms of Overexposure: 1. Shortness of Breath 2. Difficulty Breathing 3. Coughing and phlegm production. 4. More colds or infections than usual.
B) EMERGENCY AND FIRST AID PROCEDURES
INGESTION: May cause obstruction.
INHALATION: If respiratory irritation or distress occurs, remove victim to fresh air. Seek medical attention if respiratory irritation or distress continues.
SKIN ABSORPTION: If contact to the skin, wash thoroughly with soap and water. Seek medical attention if irritation or distress continues. Seek medical attention.
EYE CONTACT: If contact with eyes, hold eyes open and flush with a steady, gentle stream of water for at least 15 minutes. Seek medical attention if irritation or visual changes occur.
PRECAUTIONS FOR SAFE HANDLING & USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Sweep up material and remove to disposal container. Mop with mild detergents or cleaning solutions. Observe all relevant federal, state and local laws.
WASTE DISPOSAL METHOD
Sweep up but avoid creating excessive dust. ADDITION TO WATER WILL CAUSE MATERIAL TO SET UP. Any approved solid waste disposal method. A slurry of material may cause plugged drains.
PRECAUTIONS TO BE TAKEN IN HANDLING & STORING
Handling: wear gloves, eye protection and wear approved respirator. Wash hands before eating, drinking, using tobacco, applying cosmetics or using toilet.
Storage: do not store, use and/or consume foods, beverages, tobacco products or cosmetics in areas where this material is stored
OTHER PRECAUTIONS
Before using any LunaCrete products, read the label thoroughly.
CONTROL MEASURES
RESPIRATORY PROTECTION
Dust mask recommended- NIOSH or OSHA approved
VENTILLATION
Use local exhaust ventilation to control emissions at its source, preventing dispersion of it in the general work area.
PROTECTIVE GLOVES
Gloves may be worn for protection if skin is sensitive. (latex, neoprene, nitrile rubber)
EYE PROTECTION
Use safety glasses, goggles or face-shields for eye protection.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
NONE
WORK/HYGIENE PRACTICES
Avoid breathing dust. Wash hands thoroughly after handling and keep containers closed. |
For additional information contact: LunaCrete® 1111 H. Enterprise Court Holly Hill, FL 32117 (866) 386-9122 - Toll Free |  | If you have already purchased access to an online video, |
|
|
Professional Products |
Online Catalog |
Complete DVD Set |
|
